5 Essential Guitar Upgrades That Will Save Your Money

If you purchased a used guitar, or just let yours go unmaintained for a good amount of time, it’s probably not sounding the way it should be. Fortunately, you don’t have to purchase a new guitar. There are plenty of guitar upgrades and modifications you can do like changing the guitar bridge parts that’ll help improve its sound and save you money in the long run.

From switching out your strings to choosing better quality picks to upgrade Guitar, here are some affordable ways to improve the sound of your guitar.

Saddles

The saddles on your guitar’s extension serve basically a similar capacity as the nut, then again, actually they lay on the furthest edge of the guitar. Similar issues can torment bad quality extension saddles; in case it’s hard for the strings to move, it will prompt inflection issues.

Switching Some Picks

Most guitarists underestimate just how much their choice of guitar parts affects their tone. Professional guitarists carry around a variety of guitar picks for a reason they use light ones for strumming, heavier ones for single-note picking, and medium gauge picks for everything else.

Sometimes the guitar case can be a thing to worry about. Consider changing that with a quality case.

Ensuring your guitar is properly set up is one of the most effective things you can do to a guitar no matter how old, new, cheap, or expensive the guitar is.

This actually applies to brand new production guitars more so than it does second-hand guitars, as there’s a good chance a used guitar has already been set up properly at some point in time.

Although you can set up your guitar on your own, we recommend buying the best guitar parts from a genuine or professional store.

Comments

How To Clean And Maintain Your Electric Guitar Fretboard

Finished and Unfinished Fretboards The guitar community is torn in a debate about whether the material of a fretboard makes any difference. Some believe that a rosewood fretboard is markedly different from ebony, while others say there’s hardly any difference. But when it comes to cleaning, you will need to be cautious. Primarily, the focus is on fretboard cleaning, but other guitar parts are involved, like the neck and tuning pegs. And if your electric guitar has a fretboard that uses unfinished wood, things are tricky, demanding extreme caution. So, it’s recommended to oil unfinished fretboards for obvious reasons. When you leave wood for a long time, it turns hard, thereby making it difficult for the truss rod-neck adjustment. Unoiled fretboards can also crack in places that look bad and hamper your guitar play. How To Start Cleaning Your FretBoard For maple fretboards, you don’t have to spend time oiling. Typically, they are pre-hydrat...

5 Gibson Guitars You Should Go For

Gibson SG is a model that was introduced in the year 1961. The splendid feature of this guitar is that it is lightweight. You can easily find the vintage Gibson guitar parts very easily for this one. It is made of mahogany wood which is quite durable and strong. It has a small and extra-thin neck that can be played by anyone. This increases the playability of the guitar in a big way. It is also cheaper than the previous Gibson models. The versatile design makes it repairable and parts for Gibson guitars are easily available. It also produces sounds that are fully balanced. However the joint on the neck is slightly weak that can affect sound quality. It can break easily and is fragile due to its super thin nature. The Les Paul model is the model that was released before the SG or Solid Guitar. This Ultima model from Les Paul is a little expensive and is a total vintage collection. These look classy, luxurious and has explicitly handcrafted features. It ha...

How to Repair Binding around the Body of an Acoustic Guitar

What is Acoustic Guitar Body Binding? Almost all acoustic guitars have some type of binding around the edges where the top and back meet the sides. Many acoustic guitars also have binding around the fretboard and peghead. Acoustic guitar binding can be made out of many different kinds of material including: various woods, plastic, or celluloid. A “true” binding around the body of the guitar is inlayed or glued in a channel cut from the body. A router is used to cut a small channel or shelf on the edges of the guitar for the binding to sit on. The binding is then bent and shaped to fit the body and glued in place. Most of the time decretory purfling strips are usually inlayed next to the binding. Purfling strips are thin laminate pieces of wood dyed different colors. You might ask, what is the purpose of binding on an acoustic guitar and why don’t all guitars have binding. Acoustic guitars have the edges bound to create stronger joints between the top, sides, and back of the...

Nethan Vines

Search This Blog