Stringing a steel string guitar

Stringing a steel string guitar – how to

A young customer, a student, recently messaged me asking me to teach him how to restring a guitar.

While I thought about how to explain to him, I also wondered that often, we talk about big issues, leaving the simplest and the most essential things unexplained. So, I decided that in this blog post, I will describe how ‘I’ restring a guitar.

It is essential to understand here that there are many ways in which people string up guitars. As long as the strings don’t slip out of the tuning post, or lose tuning, all those methods are correct.

But first a little look at guitar anatomy.

Guitar Strings is one of the important guitar parts and to take off the old strings, loosen the tuning keys (machine heads) enough and then using the notch in your string-winder, pull out the bridgepins. Do be careful about keeping the bridgepins in order, remembering which pin came out of which hole because not all strings are of similar diameter. Once a pin becomes used to a certain string size, it will not seat properly with any other string size.

If they look anything like the bridgepin on the top, you need to file it, at say, a 45° angle – like the lower of the two bridgepins. A simple hobby file will help you accomplish the task. And why should you do this?

Filing the bridgepin like this will help seat the ball-end of the string right against the bridge-plate (which is right under the top, under the bridge), as it should be, rather than it getting caught at the end of the pin. The ball-end of the string stuck on the end of the bridgepin can makes a huge difference in sound transfer. It can also move while you tune/ untune a string, making it slam against the bridge-plate, damaging it.

With the old strings off, now is the best time to give a good cleaning and rub to your guitar – especially those areas that become inaccessible with strings around – the headstock and the area between the soundhole and the bridge that comes right under the strings.

With everything dust-free and clean and with the hardware at the headstock given a little tightening, it’s time to string ‘er up!

Pull out your strings and right at the ball-end of each, pinch between the forefinger and thumb and bend it 90°. You don’t have to measure with a protractor, even a small bend will do.

This done, put each string in its hole – say a couple of inches – and close it by pushing in its respective bridgepin. Remember the groove in the bridgepin is to accommodate the string. So, when you are putting in the pin, the groove should be facing the string.

As you push down on the pin, pull up on the string. Keep pulling up till the string stops coming up. This means that is seated against the bridge-plate.

These being thick and pretty stiff, I just measure up to the next post and snip it off.

Slip in the string into the E-string machine post and just let a mm or two stick out. Then, using your string winder, start winding, even as you hold on firmly to the string. As it winds and starts getting tight to hold, place it in its slot in the nut and tighten – not too much, but just enough to keep it from slipping out of its slot on the nut.

Strings are not used to the tension they are put under. When you first tune up your guitar with new strings, the tendency of the strings is to try and return to their original position. AND THAT IS WHY new strings go out of tune and you end up thinking that there is something wrong with your guitar!!!

Once you have done that, tune up your guitar again. Again give the strings a good tug. It will go out of tune again. Tune it up again. Again give them a tug and tune up again!!

How To Clean And Maintain Your Electric Guitar Fretboard

Finished and Unfinished Fretboards The guitar community is torn in a debate about whether the material of a fretboard makes any difference. Some believe that a rosewood fretboard is markedly different from ebony, while others say there’s hardly any difference. But when it comes to cleaning, you will need to be cautious. Primarily, the focus is on fretboard cleaning, but other guitar parts are involved, like the neck and tuning pegs. And if your electric guitar has a fretboard that uses unfinished wood, things are tricky, demanding extreme caution. So, it’s recommended to oil unfinished fretboards for obvious reasons. When you leave wood for a long time, it turns hard, thereby making it difficult for the truss rod-neck adjustment. Unoiled fretboards can also crack in places that look bad and hamper your guitar play. How To Start Cleaning Your FretBoard For maple fretboards, you don’t have to spend time oiling. Typically, they are pre-hydrat...

5 Gibson Guitars You Should Go For

Gibson SG is a model that was introduced in the year 1961. The splendid feature of this guitar is that it is lightweight. You can easily find the vintage Gibson guitar parts very easily for this one. It is made of mahogany wood which is quite durable and strong. It has a small and extra-thin neck that can be played by anyone. This increases the playability of the guitar in a big way. It is also cheaper than the previous Gibson models. The versatile design makes it repairable and parts for Gibson guitars are easily available. It also produces sounds that are fully balanced. However the joint on the neck is slightly weak that can affect sound quality. It can break easily and is fragile due to its super thin nature. The Les Paul model is the model that was released before the SG or Solid Guitar. This Ultima model from Les Paul is a little expensive and is a total vintage collection. These look classy, luxurious and has explicitly handcrafted features. It ha...

How To Setup Gibson Les Paul Bridge – Installation Guide

The Gibson Les Paul is a classic electric guitar that has been a favorite of guitarists for generations. One of the most important components of the Les Paul is the bridge, which plays a crucial role in determining the guitar’s sound and playability. Here, we’ll be discussing a step-by-step guide on how to set up a Gibson Les Paul bridge, with a focus on the Tune-O-Matic bridge and its components, such as the guitar bridge saddles and guitar tailpiece . Before we get started, it’s important to have a basic understanding of the parts of a guitar bridge . The bridge is part of the guitar that holds the strings in place and allows for adjustments in string height and intonation. The Les Paul bridge, also known as the Tune-O-Matic bridge , is a popular choice for many guitarists due to its high level of adjustability and ability to improve the guitar’s intonation. Step 1: Remove the old strings. Before installing the new bridge, you’ll need to remove the old strings...

Nethan Vines

Search This Blog