FIXING A CRACKED GIBSON NECK

Do you own a Gibson guitar? Do you know what it's weakest point is? Let us show you a very common repair that we do here at the shop. The way that vintage Gibson guitar parts are constructed- with a tilt back headstock, and no reinforcing volute in the back of the neck- makes them very susceptible for breaks. The wood gets really thin right between the nut slot and the truss rod channel, and if you rock too hard, or your case isn't up to par and your roadie tosses it in the van, or your Gibson experiences any other kind of shock (airplane ride?), this is usually the first thing to give. Fortunately, in most cases, this is not a complicated repair.

Owner of this guitar came in with little hope. The neck was cracked in several places, and the more cracks, the harder it is to put together. They were also really long, following the grain of the wood.

The neck had to be properly prepped- any debris and slivers that were in the way of the pieces closing back together had to be removed. Then, with the help of lots of clamps, the pieces got glued back together and left to dry over night. The customer didn't want to spend money on going all out with the "perfect" finish job, especially since he just wanted to be sure that the repair would be effective first. Playability was the outmost concern. The back of neck got cleaned up and sanded smooth, and a thin coat of lacquer was applied to preserve the exposed wood and to make it feel consistent with the rest of the neck. It got a full set up and although you can see the scars, it is revived and functioning great!

Comments

How To Clean And Maintain Your Electric Guitar Fretboard

Finished and Unfinished Fretboards The guitar community is torn in a debate about whether the material of a fretboard makes any difference. Some believe that a rosewood fretboard is markedly different from ebony, while others say there’s hardly any difference. But when it comes to cleaning, you will need to be cautious. Primarily, the focus is on fretboard cleaning, but other guitar parts are involved, like the neck and tuning pegs. And if your electric guitar has a fretboard that uses unfinished wood, things are tricky, demanding extreme caution. So, it’s recommended to oil unfinished fretboards for obvious reasons. When you leave wood for a long time, it turns hard, thereby making it difficult for the truss rod-neck adjustment. Unoiled fretboards can also crack in places that look bad and hamper your guitar play. How To Start Cleaning Your FretBoard For maple fretboards, you don’t have to spend time oiling. Typically, they are pre-hydrat...

5 Gibson Guitars You Should Go For

Gibson SG is a model that was introduced in the year 1961. The splendid feature of this guitar is that it is lightweight. You can easily find the vintage Gibson guitar parts very easily for this one. It is made of mahogany wood which is quite durable and strong. It has a small and extra-thin neck that can be played by anyone. This increases the playability of the guitar in a big way. It is also cheaper than the previous Gibson models. The versatile design makes it repairable and parts for Gibson guitars are easily available. It also produces sounds that are fully balanced. However the joint on the neck is slightly weak that can affect sound quality. It can break easily and is fragile due to its super thin nature. The Les Paul model is the model that was released before the SG or Solid Guitar. This Ultima model from Les Paul is a little expensive and is a total vintage collection. These look classy, luxurious and has explicitly handcrafted features. It ha...

How to Repair Binding around the Body of an Acoustic Guitar

What is Acoustic Guitar Body Binding? Almost all acoustic guitars have some type of binding around the edges where the top and back meet the sides. Many acoustic guitars also have binding around the fretboard and peghead. Acoustic guitar binding can be made out of many different kinds of material including: various woods, plastic, or celluloid. A “true” binding around the body of the guitar is inlayed or glued in a channel cut from the body. A router is used to cut a small channel or shelf on the edges of the guitar for the binding to sit on. The binding is then bent and shaped to fit the body and glued in place. Most of the time decretory purfling strips are usually inlayed next to the binding. Purfling strips are thin laminate pieces of wood dyed different colors. You might ask, what is the purpose of binding on an acoustic guitar and why don’t all guitars have binding. Acoustic guitars have the edges bound to create stronger joints between the top, sides, and back of the...

Nethan Vines

Search This Blog