How To Tune A Guitar For Beginners

If you are a beginner and have decided to learn the guitar then basic knowledge about the parts of a guitar neck is very helpful. The parts of the guitar neck are frets, fretboard, tuners, headstock, and truss rod. It will help you tune your guitar. Tuning your guitar is the most important step because if your guitar is not tuned, it will not sound good and you definitely don’t want that.

So, let us first learn about the parts of a guitar neck followed by the steps to tune a guitar. So, these parts are explained below:

Frets: Frets are the raised wires that run across the width of the fingerboard. These help the strings to be shortened by pressing them down behind them. While playing the guitar, players don’t have to find the perfect spot of a note which happens with other fretless instruments like a violin.

Fretboard: Fretboard is the neck area located just below the strings. It is marked and shaped so one can identify the strings easily. It helps to press the strings at some points to get some notes. Different types of materials are used for the fingerboards where most common ones are rosewood and maple.

Headstock: Just at the end of the neck you will see the headstock placed at the end of the guitar where all the strings end. At headstock, you will see the bits which is used for tuning the guitar and these are known as tuners.

Read full article – http://ezinestack.com/how-to-tune-a-guitar-for-beginners/

Comments

How To Clean And Maintain Your Electric Guitar Fretboard

Finished and Unfinished Fretboards The guitar community is torn in a debate about whether the material of a fretboard makes any difference. Some believe that a rosewood fretboard is markedly different from ebony, while others say there’s hardly any difference. But when it comes to cleaning, you will need to be cautious. Primarily, the focus is on fretboard cleaning, but other guitar parts are involved, like the neck and tuning pegs. And if your electric guitar has a fretboard that uses unfinished wood, things are tricky, demanding extreme caution. So, it’s recommended to oil unfinished fretboards for obvious reasons. When you leave wood for a long time, it turns hard, thereby making it difficult for the truss rod-neck adjustment. Unoiled fretboards can also crack in places that look bad and hamper your guitar play. How To Start Cleaning Your FretBoard For maple fretboards, you don’t have to spend time oiling. Typically, they are pre-hydrat...

5 Gibson Guitars You Should Go For

Gibson SG is a model that was introduced in the year 1961. The splendid feature of this guitar is that it is lightweight. You can easily find the vintage Gibson guitar parts very easily for this one. It is made of mahogany wood which is quite durable and strong. It has a small and extra-thin neck that can be played by anyone. This increases the playability of the guitar in a big way. It is also cheaper than the previous Gibson models. The versatile design makes it repairable and parts for Gibson guitars are easily available. It also produces sounds that are fully balanced. However the joint on the neck is slightly weak that can affect sound quality. It can break easily and is fragile due to its super thin nature. The Les Paul model is the model that was released before the SG or Solid Guitar. This Ultima model from Les Paul is a little expensive and is a total vintage collection. These look classy, luxurious and has explicitly handcrafted features. It ha...

How to Repair Binding around the Body of an Acoustic Guitar

What is Acoustic Guitar Body Binding? Almost all acoustic guitars have some type of binding around the edges where the top and back meet the sides. Many acoustic guitars also have binding around the fretboard and peghead. Acoustic guitar binding can be made out of many different kinds of material including: various woods, plastic, or celluloid. A “true” binding around the body of the guitar is inlayed or glued in a channel cut from the body. A router is used to cut a small channel or shelf on the edges of the guitar for the binding to sit on. The binding is then bent and shaped to fit the body and glued in place. Most of the time decretory purfling strips are usually inlayed next to the binding. Purfling strips are thin laminate pieces of wood dyed different colors. You might ask, what is the purpose of binding on an acoustic guitar and why don’t all guitars have binding. Acoustic guitars have the edges bound to create stronger joints between the top, sides, and back of the...

Nethan Vines

Search This Blog